Italian Surface Finishes in UK

Valsetin 2 — Technical Data Sheet

Key performance data for Valsetin 2 — a low‑VOC silk wall system built around a tinted Primer 400 undercoat and thin silk coats. Use this sheet when specifying Valsetin 2 alongside Meteore 10 Intonaco, Klondike Classic and Sabulador Soft in architectural schemes.

Low‑VOC silk system Primer 400 tinted base Architectural satin

Valsetin 2 silk-effect wall finish — close‑up detail

NEXT‑GENERATION ITALIAN SILK WALL SYSTEM · LOW VOC · PART OF THE ARCHITECTURAL FINISHES FAMILY IN LONDON

Key specifications

Finish	Silk‑like decorative coating with a directional satin sheen. Depending on the technique, patterns range from linear “brushed silk” to softer flowered / textile effects.
Use / type	Water‑based decorative system for interior walls and ceilings in residential, hospitality and commercial projects requiring a premium silk look and documented low‑VOC performance.
Chemistry & emissions	Acrylic water‑borne binder with pearlescent and mineral components. VOC (ready to use): approx. 6–7 g/L (Cat. A/i) — well below EU limit. Indoor air quality: designed for A+ TVOC and extremely low formaldehyde emissions after curing.
Coverage (guide)	On smooth, correctly primed substrates: Valsetin 2 silk coats: approx. 7–9 m²/L per coat, depending on pattern. Primer 400: approx. 8–10 m²/L per coat. Always confirm coverage and appearance on a representative sample panel under project lighting.
Application tools	Short‑pile roller / brush for Primer 400. Stainless‑steel trowel / spatula for Valsetin 2 silk coats. Optional soft brush, glove or cloth for pattern variations. Tools are available via the Italian Surface Finishes tools & accessories range.
System products	Primer: VALPAINT PRIMER 400, tinted to match the selected Valsetin 2 shade. Applied in one uniform coat to properly prepared substrates. Finish: Valsetin 2, normally 1–2 thin coats depending on opacity and desired effect, applied with trowel / spatula and worked to create the silk pattern. Optional upgrades: in higher‑stress zones (corridors, high‑traffic spaces), Valsetin 2 can be combined with V30 / Finish V16 as described in the Valsetin 2 Soft cycle documentation.
Drying / recoat	At approx. 20 °C and 65 % RH: Primer 400: touch dry in about 2–3 hours; overcoatable after ≈ 6 hours. Valsetin 2: touch dry in approx. 2–3 hours; recoat after ≈ 4–6 hours. Careful use and light cleaning: usually after 5–7 days, depending on conditions.
Recommended use	Interior walls and ceilings in living rooms, bedrooms, entrance halls, corridors, hotel suites, boutiques, show flats and reception areas. Keep to dry, ventilated zones. For fully waterproof decorative schemes in showers and wet rooms, use E‑VOLUTION PLUS as part of Waterproof Artistic Walls as the waterproof body, and carry related silk / textile languages into adjacent dry areas.
Substrates	New or existing interior plasters, skimmed plasterboard and previously painted walls, provided they are: Sound, dry and free from dust, grease and detaching coatings. Made good with suitable fillers and sanded where required. Uniformly primed with Primer 400 to avoid banding and joint shadowing.
Colours	Tinted through the VALPAINT COLORI’ / VALCLONE system, giving a broad palette of neutral and chromatic silk tones. Primer 400 and Valsetin 2 are tinted in harmony for depth and uniformity.
Packaging	Supplied in professional pack sizes (e.g. 1 L, 2.5 L, 5 L). Confirm exact packaging at time of order with Italian Surface Finishes.

Values are indicative and may vary with substrate, job‑site conditions and applicator technique. Always produce and approve a project‑specific sample panel before large‑scale work.

Compatible substrates

Valsetin 2 is suitable for most interior vertical substrates once they are correctly prepared. Typical examples:

Gypsum plaster and skimmed plasterboard (fully cured and dry).
Cement–lime plasters that are stable and free from efflorescence.
Existing sound acrylic or vinyl paints, after cleaning and light abrasion.

Substrates must be sound, clean and cohesive. Remove loose or chalking coatings, repair cracks, fill imperfections and sand smooth. Apply Primer 400 to regulate absorption, unify colour and prepare the surface for the silk coats.

System build — Valsetin 2

The typical build‑up is:

1. Substrate preparation
Level, fill and sand as required. Remove dust, grease, unstable paint and contaminants. Ensure the surface is dry and uniformly absorbent.
2. Tinted primer
Apply one even coat of Primer 400, tinted towards the selected Valsetin 2 colour, using roller or brush. Allow to dry fully.
3. First Valsetin 2 coat
Apply a thin, continuous coat of Valsetin 2 with stainless‑steel trowel / spatula, spreading material evenly and removing excess. This creates the base silk film.
4. Second coat & effect
Apply a second thin coat and, while workable, create the chosen effect (brushed silk, flowered, textile) by controlling stroke direction and pressure. Work wall‑by‑wall to maintain a wet edge.
5. Optional Soft / V30 cycle
Where specified, follow the dedicated V30 / Finish V16 cycle to obtain a softer sheen and increased resistance as per the official Valsetin 2 documentation.

For complex geometries or large elevations (corridors, stair cores, double‑height spaces), on‑site mock‑ups are recommended to refine stroke language and stopping points before full installation.

Performance & maintenance

Performance notes

Provides a durable decorative finish for internal walls and ceilings when applied over stable, suitably primed substrates.
Intended for dry, ventilated interiors; not designed as a waterproof coating on its own.
Works as part of the broader Italian Surface Finishes architecture, alongside Meteore 10, Klondike and Sabulador systems in the same project.

Cleaning & care

Allow approximately 5–7 days for curing before first cleaning.
Dust regularly with a soft cloth or microfibre duster.
For marks, use a slightly damp, non‑abrasive cloth and mild neutral detergent. Avoid aggressive scrubbing, solvents, steam cleaning and abrasive pads which may burnish or damage the silk film.

Health, safety & environment

Water‑based, low‑VOC formulation; ensure adequate ventilation during application and drying.
Avoid contact with eyes and skin; wear suitable gloves, eye/face protection and work clothing.
Do not ingest; keep out of reach of children and untrained personnel.
Store in original, tightly closed containers between +5 °C and +30 °C; protect from frost and direct heat.
Dispose of residues and empty containers according to local regulations; do not discharge into drains or waterways.

Technical & design resources

Use the links below to access application methods, galleries, FAQs and tools for Valsetin 2, and to position it correctly alongside other architectural finishes from Italian Surface Finishes.