Sabulador Lux & Matt — Technical Data Sheet

Key specifications

*Coverage is indicative and will vary with substrate texture, absorption, dilution and desired effect. Always confirm via sample panels under project conditions.

Compatible substrates

Sabulador Lux & Matt are suitable for interior walls and ceilings when applied over properly prepared, primed substrates:

• New gypsum plaster and skimmed plasterboard (fully cured, smooth and dry).
• Prepared plasterboard with correctly treated joints and repairs.
• Sound, previously painted surfaces (cleaned, de‑glossed and primed).
• Interior masonry / render that is stable, dry and primed.

Substrates must be free from rising damp, efflorescence, loose coatings, dust and contaminants. Glossy or critical surfaces should be sanded or otherwise keyed and then primed with PRIMART 600. For complex substrates please consult Italian Surface Finishes.

System build — Sabulador Lux & Matt

The exact specification can vary with colour and project, but a typical Sabulador Lux or Matt wall system is:

1. Substrate preparation — fill, skim and sand to a smooth finish. Remove loose paint and contaminants; de‑dust carefully.
2. Primer — PRIMART 600 — apply 1–2 coats depending on substrate absorbency (see Application Guide for dilutions). Allow each coat to dry thoroughly.
3. First Sabulador coat (Lux or Matt) — apply a thin, even coat with the PV76 artistic brush, working in manageable areas to create a continuous sandy film.
4. Second Sabulador coat — after 3–4 hours, apply the second coat with PV76 in the same way, keeping a wet edge and working wall‑by‑wall.
5. Re‑brushing — after 5–10 minutes (depending on conditions), lightly re‑brush with a clean, dry PV76 to align grains and create the desired dunes, ripples or directional strokes.
6. Optional clear protection — after full cure, a compatible clear protective finish may be used in higher‑wear areas to improve cleanability.

Where Sabulador is used as the visible finish over Waterproof Artistic Walls, the substrate, waterproof build‑up, reinforcement and detailing are defined within the relevant E‑VOLUTION PLUS or associated system documentation.

Performance & maintenance

Performance notes

• Provides a durable decorative film on vertical interior surfaces when applied over stable, suitably primed substrates.
• Designed for residential, retail and hospitality interiors where sandy luminescent feature walls are desired.
• Not intended as a stand‑alone waterproof membrane for continuously wet zones; for such areas, use within Waterproof Artistic Walls build‑ups.

Cleaning & care

• Allow approximately 15 days for full curing before first cleaning.
• Dust regularly with a soft cloth, microfibre or feather duster.
• For marks, wipe gently with a damp cloth and mild neutral detergent. Avoid aggressive scrubbing that could burnish the sandy film or alter sheen.
• Avoid abrasive pads, scouring powders, bleach and solvent‑based cleaners.

Health, safety & environment

• Water‑borne decorative coating with low VOC content; Matt version with very low TVOC intent.
• Ensure adequate ventilation during application and drying.
• Avoid contact with skin and eyes; wear suitable gloves and eye protection.
• Do not ingest. Keep out of reach of children.
• Store between +5 °C and +30 °C in original, closed containers. Protect from frost and direct heat.
• Do not pour residues or wash‑water into drains or watercourses; dispose of according to local regulations.
• Consult the Valpaint Safety Data Sheet (SDS) for full safety information.

Technical & specification summary

Sabulador Lux & Matt by Valpaint, supplied and tinted in the UK by Italian Surface Finishes, is a sandy luminescent wall system for design‑led interiors. It offers:

• Highly controllable sandy texture and light‑responsive shimmer.
• Water‑borne, low‑VOC formulation with Matt offering very low TVOC content.
• Compatibility with ISF’s Studio, Academy and Approved Applicator Network for repeatable results on site.

For project‑specific specifications, mock‑ups or integration with other systems (Meteore 10, metallics, waterproof walls), please contact Italian Surface Finishes or arrange a visit to the London Studio.