Klondike Ferro — Technical Data Sheet

Key specifications

*Coverage values are indicative. Always verify on a representative sample panel under project conditions.

Compatible substrates

Klondike Ferro is suitable for sound, dry, interior substrates that have been properly prepared:

• Plaster and skimmed plasterboard (fully cured, smooth and dust‑free).
• Levelled masonry and cementitious surfaces free from rising damp.
• Previously painted surfaces that are sound, non‑chalky and correctly primed.

Friable, dusty or highly absorbent areas must be stabilised using a suitable primer/fixative as per Valpaint guidance. Textured substrates should be levelled to achieve a smooth base before the Klondike Ferro system is applied.

System build — Klondike Ferro iron‑effect finish

The exact cycle can vary according to the chosen effect and substrate condition, but a typical Klondike Ferro system in the UK follows this structure:

1. Substrate preparation — make good all defects; fill, sand and clean. Remove loose coatings and contaminants. Ensure the surface is smooth, stable and dry.
2. Primer / basecoat — apply the specified Valpaint primer and/or dedicated basecoat for Klondike Ferro to equalise absorption and provide the correct undertone. Apply with roller, ensuring uniform coverage. Allow to dry thoroughly.
3. First coat of Klondike Ferro — apply a thin coat using brush, roller or trowel to establish the metallic base. Cover the surface evenly, working to a continuous film.
4. Second Klondike Ferro coat — design stage — apply a second coat and immediately work the product with a spalter brush and/or flexible trowel to create the desired iron‑effect movement and patina. Use irregular strokes and controlled pressure to reveal metallic depth and avoid obvious repeat patterns.
5. Optional protection — in higher‑use areas or where more frequent cleaning is expected, apply a compatible clear protective finish after full cure to improve washability and resistance to marking.

Project‑specific choreography (e.g. directional streaks, panel‑reference layouts, combined concrete‑and‑metal effects) is developed through ISF sample boards and Academy training.

Drying & curing

• Touch dry: approx. 2–4 hours at 20 °C.
• Recoat interval: approx. 6–8 hours at 20 °C, depending on ventilation and film build.
• Full cure: approx. 7 days at 20 °C before intensive cleaning or application of protective sealer.

Drying and curing times are extended at lower temperatures or higher humidity. Always refer to the latest Valpaint technical documentation for detailed data.

Maintenance

Once fully cured (and sealed where specified), Klondike Ferro can be maintained as follows:

• Dust with a soft cloth or vacuum with a soft brush attachment.
• For light marks, wipe gently with a soft, slightly damp cloth and mild neutral detergent.
• Avoid abrasive pads, scouring powders, strong alkalis, bleach and solvent‑based cleaners.
• Do not use aggressive cleaning methods that could scratch or burnish the metallic surface.

Health, safety & environment

• Water‑based, low‑VOC decorative coating; use with adequate ventilation.
• Avoid contact with skin and eyes; wear suitable gloves and eye protection.
• Do not ingest; keep out of reach of children.
• Store in tightly closed original containers between +5 °C and +30 °C; protect from frost.
• Do not pour residues into drains or watercourses; dispose of waste according to local regulations.
• Refer to the official Valpaint Safety Data Sheet (SDS) for full safety information.

Technical & specification summary

Klondike Ferro by Valpaint, supplied and supported in the UK by Italian Surface Finishes, is a textured iron‑effect wall system for contemporary interiors. It offers:

• Authentic oxidised metal aesthetics on standard wall substrates.
• A water‑borne, low‑VOC formulation suitable for design‑led interiors.
• Alignment with the ISF London Studio, Academy and Approved Applicator Network for consistent results.

For project‑specific specifications, sample boards or integration with other finishes (e.g. concrete, stone and marble), contact Italian Surface Finishes or arrange a visit to the London Studio.